Design And Analysis Of Crankshaft Assignment Solution

ABSTRACT

In this study a static analysis was conducted on a cast iron crankshaft from a single cylinder four stroke engine. Crankshaft is one of the critical components for the effective and precise working of the internal combustion engine. A dynamic simulation is conducted on a crankshaft from a single cylinder 4- stroke diesel engine. Finite element analysis was performed to obtain the variation of the stress magnitude at critical locations. Three dimensional model of the crankshaft was created in Pro-E software. The load was then applied to the FE model and boundary conditions were applied as per the mounting conditions of the engine in the ANSYS. Results obtained from the analysis were then used in optimization of the cast iron crankshaft. This requires the stress range not to exceed the magnitude of the stress range in the original crankshaft. The optimization process included geometry changes without changing connecting rod and engine block. 

In order to achieve the objectives various changes in the initial design of the crankshaft were done and they were analyzed among them two cases showed the most effective results. We Design two different Crankshaft with different dimensions. Finite Element analysis of the single cylinder cast iron crankshaft has been done using FEA tool ANSYS Workbench.

INTRODUCTION

It is a large component with a complex geometry in the engine, which converts the reciprocating displacement of the piston to a rotary motion with a four link mechanism. Crankshaft consists of the shaft parts which revolve in the main bearings, the crankpins to which the big ends of the connected rod are connected, the crank arms or webs (also called cheeks) which connect the crankpins and the shaft parts. The crankshaft main journals rotate in a set of supporting bearings (main bearings) causing the offset road journals to rotate in circular path around the main journal centers, the diameter of that path is the engine “stroke’. Crankshaft must be strong enough to take the downward force of the power stroke without excessive bending. So the reliability and life of the internal combustion engine depend on the strength of the crankshaft largely. And as the engine runs, the power impulses hit the crankshaft in one place and then another. The torsional vibration appears when a power impulse hits a crankpin toward the front of the engine and the power stroke ends. If not controlled, it can break

the crankshaft.

The Shaft parts which revolve in the main bearings, the crank pins to which the big end of the connecting rod are connected, the crank arms or webs which connect the crank pins and shaft parts. In addition, the linear displacement of an engine is not smooth; as the displacement is caused by the combustion chamber therefore the displacement has sudden shocks. The concept of using crankshaft is to change these sudden displacements to as smooth rotary output, which is the input to many devices such as generators, pumps and compressors. It should also be stated that the use of a flywheel helps in smoothing the shocks. Crankshaft experiences large forces from gas combustion. This force is applied to the top of the piston and since the connecting rod connects the piston to the crank shaft, the force will be transmitted to the crankshaft. The magnitude of the forces depends on many factors which consist of crank radius, connecting rod dimensions, weight of the connecting rod, piston, piston rings, and pin. Combustion and inertia forces acting on the crankshaft. 1. Torsional load 2. Bending load. Crankshaft must be strong enough to take the downward force of the power stroke without excessive bending so the reliability and life of the internal combustion engine depend on the strength of the crankshaft largely. The crank pin is like a built in beam with a distributed load along its length that varies with crank positions. Each web is like a cantilever beam subjected to bending and twisting. 1. Bending moment which causes tensile and compressive stresses. 2. Twisting moment causes shear stress. 

There are many sources of failure in the engine one of the most common crankshaft failure is fatigue at the fillet areas due to the bending load causes by the combustion. The moment of combustion the load from the piston is transmitted to the crankpin, causing a large bending moment on the entire geometry of the crankshaft. At the root of the fillet areas stress concentrations exist and these high stress range locations are the points where cyclic loads could cause fatigue crank initiation leading to fracture.